NJ 10D-COS
Part No.: MPHS-NJ-10D-COS
CANopen Slave: Can be mounted at any point of the delivery chain
產品介紹
Features
- Complete Slave interface in closed IP40 housing
- Host connection via Dual-Port Memory or SPI
- Easy slide-in mounting without tools
- Locks and connects without additional components on the baseboard
Product Description
The universal communication module netJACK with its PCI Express interface addresses in particular the embedded market with high-performance CPUs like Intel Atom®. Alternatively, there are versions with a traditional dual-port memory and a fast serial SPI interface.
All types have the compact design of a closed IP 40 module which can be mounted without using tools. Additional costs for the device will not arise because connector and mounting rails are designed as contact areas and cut-outs on the baseboard.
netJACK can be mounted quickly and easily right before shipment - or even by the end customer.
With netJACK customers can realize the full range of communication solutions, e.g. for drives, HMI or ident systems. At the same time, additional functionalities as PLC, visualization or individual applications are possible. For customer-specific requirements, Hilscher offers a cost-optimized Design and Production Service.
Due to the Hilscher network controller netX, a 10-years delivery guarantee is granted.
Technical Details
| Product | Product Name | NJ 10D-COS |
|---|---|---|
| Product Part Number | 1652.540 | |
| Brief Description | Exchangeable Module SPI - CANopen Slave | |
| Communication Controller | netX: netX 10 | |
| Integrated Memory |
RAM: 8 MB SDRAM
FLASH: 4 MB serial Flash EPROM
|
|
| Power Supply and Current |
Supply voltage: +3.3 V ± 5 % DC
Typical/maximum current: 250 mA/300 mA
|
|
| System Interface |
Bus type: Serial or parallel dual-port memory
Connector type: 60 pin connector (SAMTEC FSI-130-03-G-D-AB)
Pin distance/pin width: 0.45 mm/0.55 mm
Dual-port-memory size: 64 KB (16 address lines), where 8 KB used by firmware (13 address lines, lowest 8 KB)
Width for the data access to the Dual-Port Memory (DPM): 8/16 bit
Serial dual-port memory interface: SPI Slave, mode 3
Baud rate: Max. 50 MHz
|
|
| Communication Interface |
Communication standard (protocol): CANopen
Interface type: ISO 11898, potential free
Connector: D-Sub, 9-pin
|
|
| Diagnostic Interface |
Type: USB or UART
Connector: Signal at host interface. Available only if integrated in host system
|
|
| Display |
Display
|
|
| Environment | Ambient temperature range for operation: -20 °C … +70 °C | |
| Device |
Dimensions (L x W x H):
Weight: < 80 g
Housing: Closed module
Protection class: IP40
Mounting/Installation: Via milled footprint holes in the carrier board and retaining brackets. No mounting accessories required.
Mounting/pulling cycles: max. 10
|
|
| Configuration | Configuration software: SYCON.net | |
| Conformity |
RoHS: yes
Reach: yes
|
|
| UL Certification |
UL type: cURus
UL file: E334100
|
|
| Conformance with EMC Directives |
CE Sign: yes
Emission: EN55011:2009; CISPR 11, class A
Immunity: according to EN 61131-2:2003
Electrostatic discharge (ESD) according to IEC/EN61000-4-2 (Air discharge method): IEC/EN 61000-4-2:2009: ± 8 kV, Criterion A
Electrostatic discharge (ESD) according to IEC/EN 61000-4-2 (Contact discharge method): IEC/EN 61000-4-2:2009: ± 6 kV, Criterion A
Fast transient interferences (Burst), according to IEC/EN 61000-4-4: IEC/EN 61000-4-4:2004+A1:2010: ± 2.2 kV, Criterion A
Surge voltage, according to IEC/EN 61000-4-5 (Communication and data lines): IEC/EN 61000-4-5:2006: 1 kV, Criterion A
|
|
| Tests |
Shock: EN60068-2-27 Ea
Vibration: EN60068-2-6 Fc
|
|
Ordering Information
- NJ 10D-COS/COS (1652.540/COS) - Exchangeable Module SPI - CANopen Slave