NRP 52-RE (TRAY)
Part No.: MPHS-NRP-52-RE-TRAY
PROFINET IO Device: Ready-to-solder netX Design in stamp size
產品介紹
Features
- Rapid alternative to an own development
- Complete Slave interface with smallest footprint
- Prototyping or SMD series production
- One hardware for all Real-Time Ethernet systems
- Host connection via Dual-Port Memory or SPI
- Combines advantages of an ASIC with the benefits of a Module
Product Description
netRAPID is the rapid and secure alternative to developing your own slave using a communication controller. As stamp-sized netX chip carrier, it is integrated into the customer hardware in the same way as a QFP part. It is designed for automated SMD series production as well as for rapid prototyping.
neRAPID 52-RE is optimized for minimum space requirements. Means the 32 x 32 mm compact netX carrier contains all necessary operating components, such as magnetics, SQI flash and netX multi-protocol chip. Its focus is on Real-Time Ethernet communication and the protocol stack will be executed in the internal RAM of the netX. With netRAPID 52-RE the hardware development is reduced to only adding network connector and LEDs. A simple 2-layer baseboard is sufficient.
Full functionality of netRAPID is enabled via licensed firmware, which needs to be acquired once and loaded during manufacturing process.
Technical Details
| Product | Product Name | NRP 52 |
|---|---|---|
| Part Number | 7670.100 | |
| Brief Description | Chip carrier with Ethernet interface | |
|
Network Controller |
netX: netX 52 | |
|
Integrated Memory |
RAM: 4 MB serial Flash EPROM | |
|
Power Supply and Current |
Supply voltage: +3,3 V DC ± 5 % Maximum current (typically): 520 mA/600 mA (at 3,3 V) Power consumption (typical): 1.8 W |
|
|
Host Interface |
Type: Parallel dual-port memory or serial dual-port memory (SPI, mode 3) Connector: 76-pin solder contacts 1 mm with 1.5 mm grid Dual-port memory size: 16 KB (14 address lines) Width for the data access to the dual-port memory (DPM): 8 or 16 bit Baud rate (serial dual-port memory): Max. 50 MHz |
|
|
Communication Interface |
Communication standard: Ethernet Interface type: 100BASE-TX or 10BASE-T, isolated |
|
|
Diagnostic Interface |
Type: USB or UART, the support of the diagnostic interface depends on the loaded firmware Connector: USB or UART: Signals at Chip Carrier, available only if integrated in host system |
|
| Display |
LED displays:
|
|
|
Permitted Ambient Conditions |
Ambient temperature range for operation: -20 … +70 °C (at an airflow of 0.5 m/s) | |
| Device |
Dimensions (L x W x H): 32 mm x 32 mm x 4 mm Weight: approx. 4 g |
|
|
Conformance with EMC Directives |
Emission: EN 55011:2009 + A1:2010 Class B (Conducted), A (Radiated) Electrostatic discharge (ESD) according to IEC/EN 61000-4-2:1995 (Contact discharge method): 6 kV Criterion A Radiated RF, according to IEC/EN 61000-4-3 and IEC/ EN 55011 80-1000MHz, 10V/m, 80% AM / 1kHz: Class A Radiated RF, according to IEC/EN 61000-4-3:2006 1.0-2.7 GHz, 10V/m, 80% AM / 1kHz: Class A Fast transient interferences (Burst), according to IEC/EN 61000-4-4:1995 (Communication and data lines): 2.2 kV Criterion B Surge voltage, according to IEC/EN 61000-4-5:1995 (Communication and data lines): 1 kV Criterion B Conducted RF, according to IEC/EN 61000-4-6:2009 0,15-80 MHz, 80% AM / 1kHz: Class A |
|
Ordering Information
- NJ 52-RE(TRAY) (7672.100) - netX Chip carrier - PROFINET IO Device