COMX 100CA-DN (M/S)
Part No.: MPHS-COMX-100CA-DN+M(+Master Licence)
MPHS-COMX-100CA-DN(Slave only)
DeviceNet Master/ Slave: The module for all communication tasks
產品介紹
Features
- Universal DeviceNet interface with network connector onboard
- Host connection via dual-port memory
- Master or slave on the same hardware
- Allows one baseboard design for all networks
Product Description
The comX communication module has been designed to be integrated into automation devices e.g. robot controllers, PLCs or drives to add a network interface. All communication tasks are executed autonomously within the module - irrespective of the processor of the target device.
Process data is exchanged via a Dual-Port-Memory which is accessed either by an 8-/16-bit bus interface or a fast 50 MHz SPI interface.
comX supports all major Real-Time Ethernet protocols as Master or Slave and covers all network-specific demands in just one single module. To support a line topology, the module is equipped with two Ethernet ports. The communication protocol can be changed simply and reliably by loading the appropriate firmware and a software license for masters.
Technical Details
| Product | Part Number | 1531.510 |
|---|---|---|
| Brief Description | Communication Module DeviceNet | |
|
Communication Controller |
netX: netX 100 | |
|
Integrated Memory |
RAM: 8 MB SDRAM FLASH: 4 MB serial Flash |
|
|
Power Supply |
Supply voltage: +3.3 V DC ± 5 % Typical/maximum current: approx. 440 mA/470 mA (at 3.3 V) Typical power consumption: approx. 1.5 … 1.6 W Power connector: via system bus connector X1 |
|
|
System Interface |
Type: Parallel Dual-port memory interface Connector: 50-pin SMT, female connector Pin distance: 1.27 mm Dual-port memory size: 16 KByte Data width: 8/16 bit |
|
|
Communication Interface |
Communication standard: DeviceNet Interface type: ISO-11898, according to DeviceNet specification, potential-free Connector: COMBICON connector, 5-pin |
|
|
Diagnostic Interface |
Type: UART or USB Connector: Signal at host interface. Available only if integrated in host system. |
|
| Display |
LED display: SYS System Status, green: RUN, yellow: RDY MNS Module network status, green: MS, red: NS |
|
| Environment |
Ambient temperature range for operation: -20 °C … +65 °C (Air flow during measurment: 0,5 m/s) Ambient temperature range for storage: -10 °C … +70 °C Humidity range: 10 % … 95 % relative humidity (non-condensing) |
|
| Device |
Dimensions (L x W x H): 70 mm x 30 mm x 21.5 mm Weight: approx. 35 g ... 40 g Mounting: using screwable metal bolts, according to comX Design Guide |
|
| Configuration | Configuration software: SYCON.net | |
| Conformity | RoHS: yes | |
|
Conformance with EMC Directives |
CE sign: yes Emission: EN 61000-6-4 Immunity: EN 61000-6-2 Electrostatic discharge (ESD) according to EN 61000-4-2 (Air discharge method): EN 61000-4-2: ± 8 kV, Criterion B Electrostatic discharge (ESD) according to EN 61000-4-2 (Contact discharge method): EN 61000-4-2: ± 4 kV, Criterion B Fast transient interferences (Burst) according to EN 61000-4-4: EN 61000-4-4: ± 2 kV, Criterion B (Communication lines and DeviceNet power supply, unshielded) Surge voltage according to EN 61000-4-5 (Communication and data lines): EN 61000-4-5: 1 kV, Criterion B (Communication lines); 1 kV, Criterion B (DeviceNet power supply 24V---PE, GND-PE, unshielded); 0.6 kV, Criterion B (DeviceNet power supply 24V---GND, unshielded) |
|
Ordering Information
- COMX 100CA-DN/DNM (1531.510/DNM) - Communication Module Dual-port memory - DeviceNet Master