PCAN-USB X6
Part No.: MPPK-IPEH-004062 (D-Sub connectors)
MPPK-IPEH-004063 (M12 circular connectors galv.isolated)
MPPK-IPEH-004064 (D-Sub connectors galv. isolated)
The PCAN-USB X6 is a CAN FD adapter for the USB port which allows the connection of up to 6 CAN FD or CAN busses.
*標高電子為德商PEAK SYSTEMS台灣唯一代理商。
產品介紹
Description
The PCAN-USB X6 is a CAN FD interface for the USB port which allows the connection of up to 6 CAN FD or CAN busses. The device is therefore best suited for working with multiple CAN networks like the use in test benches with hardware-in-the-loop (HIL) simulations for motor vehicles or in the product line testing of CAN-based products.
The PCAN-USB X6 is installed in an aluminum profile casing and is shipped in versions with D-Sub connectors or M12 circular connectors. Especially the M12 version is suitable for use in harsh environments. In addition, a galvanic isolation of up to 300 Volts between the PC and the CAN side is guaranteed for the decoupled versions.
The new CAN FD standard (CAN with Flexible Data rate) is primarily characterized by higher bandwidth for data transfer. The maximum of 64 data bytes per CAN FD frame (instead of 8 so far) can be transmitted with bit rates up to 12 Mbit/s. CAN FD is downward-compatible to the CAN 2.0 A/B standard, thus CAN FD nodes can be used in existing CAN networks. However, in this case the CAN FD extensions are not applicable.
The monitor software PCAN-View and the programming interface PCAN-Basic for the development of applications with CAN connection are included in the scope of supply and support the new standard CAN FD.
Specifications
- CAN-FD interface for High-speed USB 2.0 (compatible to USB 1.1 and USB 3.0)
- 6 High-speed CAN channels (ISO 11898-2)
- Comply with CAN specifications 2.0 A/B and FD
- CAN FD support for ISO and Non-ISO standards switchable
- CAN FD bit rates for the data field (64 bytes max.) from 25 kbit/s up to 12 Mbit/s
- CAN bit rates from 25 kbit/s up to 1 Mbit/s
- FPGA implementation of the CAN FD controller
- NXP TJA1044GT CAN transceiver
- Alternative pluggable transceiver modules on request
- Galvanic isolation on the CAN connection up to
- 300 V (only for IPEH-004063 and IPEH-004064)
- Status LEDs for CAN channels, USB upstream, and power supply
- CAN connection via D-Sub, 9-pin or M12 circular connectors, 5-pin (pin assignment of both connectors in accordance with CiA® 303-1)
- Aluminum casing with increased Ingress Protection IP64 (only for IPEH-004063)
- High-speed USB 2.0 downstream port (only for IPEH-004062 and IPEH-004064)
- CAN termination can be activated through a solder jumper, separately for each CAN channel
- Measurement of bus load including error frames and overload frames on the physical bus
- Induced error generation for incoming and outgoing CAN messages
- Voltage supply from 8 to 30 V
- Extended operating temperature range from -40 to 85 °C (-40 to 185 °F)
Pin Assignment D-Sub
| Pin | Pin Assignment CAN |
|---|---|
| 1 | not connected |
| 2 | CAN-L |
| 3 | GND |
| 4 | not connected |
| 5 | not connected |
| 6 | GND |
| 7 | CAN-H |
| 8 | not connected |
| 9 | not connected |
Pin Assignment M12
| Pin | Pin Assignment M12 |
|---|---|
| 1 | Shield |
| 2 | not connected |
| 3 | GND |
| 4 | CAN-H |
| 5 | CAN-L |
Product Includes...
- PCAN-USB X6 in aluminum casing
- IPEH-004062 and IPEH-004064: Mating connector for power supply (Phoenix Contact MC1,5/2-STF-3,81 - 1827703)
- IPEH-004063: Cables for power supply and USB connection
- Device drivers for Windows® 11, 10, 8.1 and Linux (32/64-bit)
- CAN monitor PCAN-View for Windows®
- Programming interface PCAN-Basic for developing applications with CAN connection
- Programming interfaces for standardized protocols from the automotive sector
- Manual in PDF format
Note:
1. The scope of supply does not contain a power supply unit for the device. There is no supply via the USB connection to the PC.
2. Prices and Specifications are subject to change without notice